E21 Lecture #20

Microcontrollers

Wrap-up

Peripheral Control

Each peripheral is a state machine that is set by moving information to and from registers

Peripherals can communicate asynchronously with the processor through the use of interrupts

Interrupts

What are they?

  • A method that an asynchronous process can communicate with the processor
  • I/O is slow, for example, compared to the processor speed

How are they implemented?

  • An interrupt bit is set when a device signals for an interrupt
  • The processor saves its current instruction on the stack and disables interrupts
  • The processor then enters an interrupt service routine
  • The processor polls the interrupt flags to find
  • The processor takes care of the situation that caused the interrupt
  • The processor then returns to the instruction just after the interrupt occurred
  • Interrupts are re-enabled on the return
  • Interrupt timing diagram shows the process (pp. 8-10 of reference manual)

On the PIC the interrupts all come into a single line

  • A couple of big OR gates (pp. 8-4 of reference manual)
  • The GIE (Global Interrupt Enable) bit is ANDed with the Interrupt input line
  • The interrupt service routine must poll the interrupt flags to see what caused the interrupt
  • More than one interrupt could happen at the same time, so the polling order is important

A/D conversion using Interrupts

  • Converter uses three registers to control operation, plus the A/D interrupt flag and the A/D interrupt enable bit
    • ADCON0: controls the operation of the converter
      • Bits 7:6 control the sampling frequency by specifying a divider on the internal clock
      • Bits 5:3 specify which line to read
      • Bit 2 is how you tell the A/D converter to begin, it resets the bit when it is finished
      • Bit 1 is reserved
      • Bit 0 turns the A/D converter on (1) or shuts it off so it doesn't draw current (0)
    • ADCON1: specifies the functionality of the A/D pins
      • Bits 7:3 not used
      • Bits 2:0 specify which pins are Analog, which pins are Digital, and whether to use an external reference instead of the internal reference voltage source
    • ADRES: Holds the result of the conversion
  • Process
    • Configure the A/D module
      • Configure the converter pins (ADCON1)
      • Select the input channel (ADCON0)
      • Select the input clock (ADCON0)
      • Turn on the A/D module (ADCON0)
    • Configure the A/D interrupt
      • Clear the ADIF bit
      • Set the ADIE bit (enables or disables interrupts)
      • Set the GIE bit (enables or disables all interrupts)
    • Wait the required acquisition time so the A/D capacitor can charge
    • Start the conversion (ADCON0)
    • Wait for the conversion to finish
      • Poll the GO/DONE bit
      • Wait for the interrupt
    • Read the A/D result register
      • Clear the ADIF bit, if required

Microcontroller Flow Chart

Look at some specific instructions and how they would work

  • MOVF: move from register F to W or back to F (to set status flags)
    • Decode, Read, Process (run through the ALU), Write
  • ADDWF: add contents of W to contents of F and put result in W or F
    • Decode
    • Read (using either direct or indirect address)
    • Run through the ALU
    • Save to either W or F
  • CALL
    • Decode
    • Latch PC+1 to the top of the stack
    • Latch 11-bit literal and top two bits (PCLATH) to PC
    • Second cycle is no-op instructions while new PC value is being fetched into the IR
  • RETLW
    • Decode
    • Read literal
    • Send it through the ALU and put in the W register
    • Load PC from the top of the stack
    • No-op instructions during second cycle while new PC value is used to fetch next instr.
  • BTFSC: Bit test register F, skip if the bit is clear
    • Decode
    • Read register F
    • Pass it through the ALU to set status flags
    • No-op on write cycle
    • If the bit is clear, this becomes a two-cycle operation and No-ops are performed for one cycle while the instruction after the skipped instruction is fetched
    • If the bit is set, the next instruction is executed

VHDL: VHSIC Hardware Description Language

Why do you want a hardware description language?

  • To simulate hardware before implementing it
  • To make design entry simpler than moving boxes and connecting wires
  • To simplify verification and testing
  • To simplify communication between different tools in a CAD environment

VHDL offers a standard language (IEEE Standard 1076 plus some additional standards)

  • There are competitors (AHDL, Verilog HDL)
  • Latest VHDL standard is 1993
  • Standard 1164 standardizes data types for simulation
  • Standard 1076.3 standardizes data types as they relate to hardware

How do you use VHDL?

  • Design specification stage
  • can describe subcomponents in VHDL using input/output specifications
  • Design entry
  • following certain styles of VHDL, you can map VHDL onto hardware
  • Design simulation
  • you can simulate your design before putting it into hardware
  • Design documentation
  • since VHDL is a standard, you can use the VHDL code as a formal specification
  • provides an alternative to schematics
  • provides an alternative to proprietary languages (Altera's AHDL is one example)

What is the overall structure of a hardware description language?

  • At its essence, the HDL consists of methods of describing the two parts of a circuit
  • The input/output characteristics of the circuit (entities)
  • The internal functioning of the circuit (architectures)
  • The other main structures of the language are designed to allow hierachical design

Simple Example 1: A comparator

entity compare is
port(A, B: in bit_vector(0 to 7);
EQ: out bit);
end compare;

architecture compare1 of compare is
begin
EQ <= `1' when (A=B) else `0';
end compare1;

The Entity: Compare

  • The entity describes the input/output behavior of the circuit
  • bit is a data type that describes a single wire carrying a Boolean value
  • bit_vector is a data type that describes a set of wires carrying Boolean values
  • The architecture describes the function of the circuit
  • When the bits on the A and B wire sets are identical, then the circuit outputs a `1'
  • Otherwise, it outputs a `0'
  • The conditional assignment statement is a basic tool of VHDL
  • Note the architecture has to have a unique name, since there can be more than on architecture for a given entity
  • A complete VHDL design must contain at least one entity and at least one architecture for that entity.

Other major language elements

  • Packages
  • Like the class declaration for a C++ class
  • Specify constants, data types, function prototypes, aliases, etc..
  • Tell the rest of the world how to use the functions declared in the related package body
  • Package Body
  • A set of functions/routines/circuits you can put into a library for reuse
  • Configurations
  • Specify which architectures go with which entities, etc.

Design Levels

  • Behavioral
  • Dataflow (Register-Transfer Level)
  • Structural